Something new this weekend – Z-Wave (EU) Yale Lock and automation dashboard

Finally got my Z-Wave (EU)-enabled Yale smart lock from my friends at L3 Homeation [http://l3homeation.com/] (Kallang Leisure Mall)

It shows up as a lock in the Vera interface:
I also finally found a use for my Galaxy Note 10.1 tablet that’s been collecting dust. 

A work in progress….

Advertisements

Setting up the Aeon Labs MiniMote with the VeraLite (UI6) to control Blinds

I motorized my blinds and curtains, but I realized it may be too complicated for some family members to operate. I decided to get a few Z-Wave remotes to assist.

I eventually settled on the Aeon Labs MiniMote due to it’s size and features (control up to 8 scenes). (Special thanks to http://www.domotics.sg/)

Setting up is relatively simple. I ignored the instructions that came with the remotes as they were confusing (product of poor translations from another language to English?). I found this forum post that pointed me in the right direction.

Start by going to Add Devices.

Select the Advanced Z-Wave devices.

Finally press the Add one button to add it as a primary controller.

 Once pressed, the yellow light on the VeraLite will flash. At this point, find the “Learn” button on the MiniMote. Press that. You’ll see several flashing lights on both devices. When the yellow light on the VeraLite goes solid, you’re ready to continue.

Refresh the UI6 interface. You should see a new “Other”device, named something like “_MiniMote”. I like to name all my devices, so click on the wrench.

Go to Advanced. Replace the name field with what you want. Then press the X button at the top right. That’s it. (you’ll need to reload your interface so the changes are saved)

Lastely, the MiniMote deals directly with Scenes. I already had several scenes configured in my VeraLite for my blinds and curtains. Click on the wrench again, then the scenes tab. Here you can easily select existing scenes to be run when a button is pressed.

Once you’re done, and the interface is saved, you’re ready to use the device!

Prepping for Arduino Sensors with Vera (Z-Wave) Controller

I posted about my recent purchase of the Vera Lite Z-Wave controller the other day in a rather ambiguous blog title. Since then, I’ve been researching ways in which I can build my own sensors that would ultimately be much cheaper than buying ready-made Z-Wave sensors.

I came across this website that details a project that allows you to build your own sensors using Arduino, and it plugs directly into a Vera. On average, the sensors should cost anywhere around USD 10, but I’ll see what the actuals will be after I get all the pieces.

My initial plan is to get the following sensors built:

  1. Temperature for each room of the house (5 or 6)
  2. Humidity+Temperature for the two bathrooms (more on this later!)
  3. Barometric pressure+Temperature for outside (for fun)
I thought about trying to locate most of this stuff in Singapore but I figured I’d end up paying more than double of what I would if I sourced from China myself (and not to mention the time it would take for me to drive around and locate everything!)
The above linked project site was nice enough to link to individual products on eBay, so I decided to dust off my old eBay account and get purchasing.
Phase 1 cost me just about USD 120 (or about SGD 160) for the raw materials. This should get me a good 8 different sensors. Compare this to getting a Z-Wave-enabled Fibaro Universal sensor at GBP 36, plus the cost of the actual sensor chip – I think going this DIY route will save quite a bit of money. 
Future Plans
I have some thoughts of what to do in “Phase 2”. Building on the base, I want to do the following:
  1. Automated bathroom exhaust fan (using the humidity sensor)
  2. Automated plant waterer (using the not-yet-purchased moisture sensor)
I’ll report back when I get the devices. Work can’t start until I move in April or so any way..

Putting the pieces together in anticipation…

It’s been a while since I posted here. Primary reason, I had a daughter last March. (my free time disappeared literally overnight). Now that we’re getting settled, it’s time to get back into the home automation game.

In anticipation to our upcoming move to our first home we’ll own, I am ramping up and have decided on the Z-Wave protocol as I don’t want to built my own everything from scratch, but instead I’d like to get a baseline on which I can build on top of.

Will I still hack around with the Raspberry Pi? I think so. More on that later.

The Base

As mentioned above, I decided on Z-Wave. (Other competing standards include ZigBee). I ultimately went with the Vera Lite controller that I kind of bought out of the blue the other day at the IT Show here in Singapore (it was discounted by 10%, but it’s still more expensive in Singapore than elsewhere because it is Singapore).

The kit included the controller (the Vera Lite), 3 Fibaro dimmer switches, and a motion detector. The dimmer switches will be used for connecting some of my downlights to the network (and I am sure I’ll need more later).

Lighting

I bought 12 LIFX bulbs a while back and they arrived a couple of weeks ago.

No, these don’t talk Z-Wave, but that will be a fun project for me, see below.

As mentioned earlier, I’ll be using dimmer switches (or normal switches) for my other lighting. Even though these switches are expensive (if they are Fibaro), the advantage is, they are small and should fit inside of the light switch socket in the wall (I haven’t confirmed this yet with our new condo, so fingers crossed).

My LIFX bulbs will be placed in both ceiling lights as well as lamps, but the final configuration isn’t yet confirmed (I still have about 3 not yet taken as I am struggling to find rail lights that fit E27 Edison screw bulbs. Tall order.

LIFX is planning to release an SDK sometime this quarter, they claim. Once they do, the hacking begins – I want to build a Z-Wave interface for LIFX, most likely using a Raspberry Pi with Z-Wave shield (it’s a shame that it’s bloody expensive though – more than the Pi itself!).

Aircon and other IR Devices

This is where the fun begins. I was thinking of continuing my previous project of the “ThermostatPi” (which I coincidentally posted about a year ago yesterday), making use of a Raspberry Pi and a USB Toy 2, but following a Singapore Home Automation forum on Facebook the last few months, a very interesting product out of China has stoked my interest, the Broadcom RM2. It’s a proprietary IR blaster (i.e. that doesn’t connect with any other Home Automation standard like Z-Wave), but the reviews promise it “just works” – something I am quite keen on. They are rumored to release an SDK for it in Q1 of this year. And this is where another fun project will come about as I plan to write a RaspberryPi interface to it, much like I plan to do with LIFX as stated above. The goal here is to control everything from single app (switching between apps is too much trouble and certainly not consistent with the whole Home Automation thing).

Curtains

I’m still researching this and will post more about what plan to do. It looks as though the mechanisms to control curtains is quite costly, so this may need to take a back seat for a while.